Longmont Paintless Dent Removal Cost

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Longmont .

Paintless dent repair crease

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Repair at Home

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Pop a Dent

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Longmont  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Auto Dent Repair

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless dent repair crease

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless dent repair light

Longmont

Paintless Dent Removal Techniques: How To Do It Yourself

It can be frightening when you get stuck in a hail storm but the truly scary part is what it can do to your car. You wouldn't think that little chunks of ice could do much damage to sheet metal. However, many people have been left with a car that looks like a golf ball after a nasty winter storm. Auto Hail Damage Repair has changed a lot over the years and can be done in some cases without the need for a new paint job.

For years the standard way to remove dents was by pulling the dent out. You would have to drill holes into the dented area and use a tool to pull the metal back into shape. Then you would have to grind the holes down and use a body filler to smooth them over. After that you would repaint the damaged area and that is one of the biggest drawbacks to this procedure. A paint job that was put on by the manufacturer is of extremely high quality. It is nearly impossible to duplicate it without taking it back to the manufacturer. So you would be left with a section of car that was obviously repainted with inferior materials.

Paintless Dent Repair was invented specifically for this reason. The Mercedes-Benz Company in Germany was having a lot of trouble shipping their cars to the various dealers. When they arrived they would have dents and dings but the car lot would not have the resources to give them a manufacturer quality paint job after they were repaired. So they developed a procedure for Paintless Dent Removal that uses rods to push the dent out from the inside while gently tapping the outside with a hammer. It is important that the technician be very skilled using Paintless Dent Repair techniques because if they strike the metal too hard it will split. Sometimes glue is used on the outside of the car to pull the dent instead of pushing with rods which can eliminate the need for using a hammer on the metal. The only times that Paintless Dent Removal is not possible is if the paint was damaged by the initial impact or if the metal has been stretched too far out of shape.

Paintless Dent Repair is a great way to save money and retain your original manufacturer paint job. Just make sure that the repair shop that you choose is reputable and has done it many times before. To find a local repair shop you can search the internet for Paintless Dent Repair North Georgia.

Paintless Dent Removal

PDR stands for paintless dent repair. It's a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn't take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops.

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It's a new way of fixing dents and dings that is putting the car repair world at notice!

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Longmont  

Auto Hail Damage Repair

Paintless Dent Repair at Home

COLORADO Paintless dent repair light

Fountain Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Fountain .

Pop a Dent

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Repair Course

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless Dent Repair at Home

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Fountain  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Pop a Dent

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Auto Dent Removal

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Removal Cost

Fountain

Paintless Dent Repair: Myths and Facts About Car Dent Repair and Insurance

Nowadays, the most popular technique for removing dents in your car is paintless dent removal (PDR). Depending on the degree or level of repair for your car, the techniques used in PDR vary although the basic methods are similar. Special tools will be used for applying PDR in order to straighten out or fix dents. The basic method involves gradual pushing of the metal so that it would return to its proper place. Although PDR involves a slow process, it can produce great results for your car especially when it is done properly. More so, your car paint would not be damaged when PDR is applied.

Special kinds of dent removal tools are used in PDR. Skilled operators use these dent removal tools in order to remove or fix dents on your car. These tools are usually flat and long so that they can reach even small gaps like window slots. More so, these tools are able to slide into place to put pressure on the metal. A long flat tool is used in gaps that are usually behind the panel. A skilled operator will then guide the flat tool to the dent and press it to push the metal back into place. The operator will also handle the flat tool in such a way that it massages the surface where the dent is and moves it back into shape.

Paintless dent removal is highly advantageous regardless if your car has small dents or minor damages. This is because it makes use of special tools that do not damage the paint of your car. More so, it is much cheaper as compared to other methods of dent removal. It provides great outcomes for your car when handled or applied by a skilled operator. Thus, you not only save money but time and effort as well.

Paintless Dent Repair Course

Repairing dents is often done with a drill or a dent puller and sometimes even a grinder and some related tools. Those dents that don't come with missing paint, or chips and cracks can be completely or almost completely rectified with processes related to paintless dent repair. You will find these methods require the simplest of tools that you will find ordinarily in your garage. It will save you the hassle of taking your car to the body shop and allow you to save some money.

One technique of going about paintless dent removal is the household method. Here you will need a simple household plunger. The style really doesn't matter. Dampen the dent with some water and put on some car washing liquid or soap on it. You need to do this to create suction. Place the plunger over the dent and press. Make sure the pressure is not so high that you end up making a bigger dent. Once the suction is created, use the normal suction method and pull at the plunger. This will get rid of the dent for you. You can do this as many number of times you please and get the metal back in place. It will not affect the car body in anyway. The plunger is a simple way of pulling the metal back in place without having to get a professional to do it.

The other method is the hammer and dolly one. There are some dents that a plunger will not be able to handle. If you have a dent that is accessible from two sides then you could go to a automotive store and get a metal dolly and a body hammer. In case you can't a block of wood will serve the purpose, but it has to be a inch thick and fresh. If the dent has any plastic liners around it, remove them from place. Put your wooden dolly on the back of the dent and tap on the body with the hammer. Don't hit, but tap. Hitting will create a bigger dent and may even chip the paint. Do this repeatedly and slowly and you will be able to get the dent out of the way.

Of course, a person might become a bit concerned of getting quality results in their dent repairs. DIY repair methods, while a cheap option, can produce unsatisfactory results. Automobiles are expensive investments and if the owner wants to restore them to their peak condition and value, then it is recommended that they consult a paintless dent repair company to have the dent removed. Most paintless dent repair companies employ trained, certified paintless dent repair technicans and utilize the latest in industry PDR methods. By engaging a certified PDR technician, the car owner has the peace of mind of knowing that their car will be restored to its pre-dent condition and value.

Fountain  

Paintless Dent Repair: Myths and Facts About Car Dent Repair and Insurance

Paintless Dent Removal

COLORADO Paintless dent repair light

COLORADO Paintless dent repair light

Paintless Dent Repair or PDR is a group of procedures used in COLORADO for fixing little dents and dings from the body of cars, buses and vans. A variety damages can be repaired through the paintless dent repair method. Some of the common repair types of damage include stone dents and bumper repair.

Paintless Dent Repair at Home

The methodologies for paintless dent repair utilize body picks and metal rods to push the damages out from the inner side of the body panel being repaired. A special kind of adhesive may also be used on the external side of panel to pull the dents out. In both the instances, fine-tuning of the dent removal usually involves “tapping” down the ding to take away small spots, making the surface flat and shiny.

The technicians access the dent from window openings, by taking out headlights and tail lights and through wheel well openings. After getting access to the inside surface of the body work, gentle pressure is applied until the dent is removed. Since PDR works from behind the vehicle’s damage, no sanding or putty work are required. Paintless dent repair is used on both aluminum and steel panels. In COLORADO skilled dent repair Techs removes up to 100 per cent of the damage using specially devised PDR procedures. These tools and procedures provide a large range of flexibility and rigidity, with tips tapered and configured to allow for repair to any kind of damage on any type of vehicle. Once the repairs are completed there is no visible or apparent support that a dent was ever there.

Pop a Dent

Some of the great benefits of Paintless Dent Repair are:

• There is no repainting or body filler used.

• It proves to be less expensive than standard body repair.

• The service is done within a few hours.

• The issue of paint over-spray on other areas of vehicle is eliminated.

• There is no risk of color mismatch.

• The vehicle retains its original paint.

A vehicle with showroom paint usually carries a better value than a repainted vehicle. Even if it is just a door or the fender, it is always smart to maintain the original paint as long as possible.

Dent Repair shops based in COLORADO offer expertise for the professional quality of paintless dent removal and scratch repair. Plastic Bumper Repair, automobile scratch and stone chip repairs and hail ding repairs are a few other services that can also be supplied. The paintless dent repair method used by these shops preserves the vehicle value as it maintains the original paintwork.

Pop a Dent

Paintless Dent Removal Techniques: How To Do It Yourself

Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?

Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.

Why the popularity

PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.

The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.

The car does not need re-spraying and this brings down your overall costs.

Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.

Is paintless dent removal for you?

As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.

PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.

The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.

Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.

Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.


Loveland Paintless Dent Removal Cost

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Loveland .

Paintless dent repair light

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Auto Dent Repair

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Pop a Dent

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Loveland  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless Dent Repair Course

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Car Dent Remover

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair at Home

Loveland

A Quick Guide to Paintless Dent Repair

Owing to the reasons that paintless dent repair is fast and efficient it is quickly becoming popular. But there is a dearth of trained professional technicians who are skilled in the techniques that are required for this trade. If after training you want to start your own business then here are some tips to keep in mind when starting your Paintless Dent Repair (PDR) Business.

1. Survey the Market:

It is very important that you consider your potential market. Decide who you will work with? Do you have any connections at a body repair shop, wholesalers, car dealer, detail shop, service centre, etc who will hire you once you complete your paintless dent removal course?

2. Survey your Competition:

Collect information about how many paintless dent removal technicians there are in your area and how are they operating in your potential market. What are the charges for their services and what kind of a relation does your competition have with your potential market as well. Note all these things down for reference.

3. Register your Business:

Check out your state government's website and get information about how to register your business. Make sure that you choose a business name that connects you to the paintless dent repair industry and you could even use the words like dents, dings, dent repair, etc. Complete the entire registration process or even get some professional help.

4. What are your State's Requirements?

The rules and regulations vary from state to state and so it is important that you are completely aware of all the requirements for setting up a PDR Business. You may need business insurance, sales license, shop space, etc. You could ask a local dealer or the office manager of a PDR company what their dealers require from their vendors that is you.

5. Get Trained and buy the Tools:

You need to get trained at a very good academy so that you are well versed in the techniques and skills required in this business. You could consider the name Dents R Us for your paintless dent removing training. For more info check them out at http://www.dentsrus.com.au. You will also need to buy your tools for the job and you need to practice as much as possible.

6. Get Business Material:

You will need office stationery, business cards, invoices, etc and even some accounting material.

7. Don't quit your Current Job!

It is important that you keep your current job as you will need some income to support the business and the family till you are really on your way.

8. Practice on your Acquaintances:

As you begin your business you will need as much practice as you can get and one of the best ways is to practice with the cars belonging to your connections and acquaintances. Of course not many people will hand over the keys to their BMWs, until you are sure of your skills but till then you can even ask your local body shop to give you some work for no pay.

9. Pitch yourself:

You need to be your best marketing strategy. You need to start talking about your work to potential clients or people who will get you work. You need to show them what you are capable of and you need to convince them that you are only getting better and it is YOU that is working for them. Be responsible and you will get recommendations.

10. Legalities:

Last but not the least, finalise your legal businesses and tie up the loose ends in regards to conducting your business as a vendor to body shops to dealerships.

These are few things you could keep in your mind when starting out. Hopefully they have been of some help.

Car Dent Remover

PDR, a better repair!

First let me start by explaining what PDR or Paintless Dent Removal is for those of you out there that have never heard the term. PDR is conceptually simple, put simple it is the process of removing damage from an automotive body panel without the need for sanding, grinding, body-fillers or painting (hence the term Paintless).

The process of removing damage to vehicles without then need for painting is actually not new at all, though industry folk lore varies from tale to tale, Mercedes Benz allegedly began having "metal-men" work small imperfections in panels while still on the assembly line as long ago as the 1950's. Today's PDR technicians have adapted various techniques for removing dings and dents from vehicles without the need for fillers and re-painting almost as an art form. Better tools, training and advances in automotive clear coat durability have led to miraculous results for even large dents.

Why can't I just use a dent popper like the ones you see on TV?

Unfortunately the dent poppers, suction cups and (this one makes me chuckle) dry ice simply don't work. First let's explore the "screw out dent poppers". You've probably seen the late night Ding King infomercials showing you how easy it is to just glue on the tab, place the lifter on the tab and turn. POP! the dent's gone! right? Wrong! the commercial never shows the large high spot, low spot still left or heaven forbid the high spot surrounding a low, or as i like to call them a "volcano". The main reason this is a gimmick, missing tools and knowledge. Professional PDR technicians actually do use a method of removing some select dents from the front of a panel with tabs, special adhesives and a lifting apparatus.

The main difference? a technicians main assets are their eyes, reflective source, and hand-eye-coordination. a professional technician assesses the dent with a reflective source, be it a light, line board or reflective pole, and targets the "dead-center" of the dent. Once located the technician places a tab directly at this zero point and then uses a lifting device to bring the depressed metal as close to level as possible in one pull. Once the pull has been made the technician removes the tab and assesses the area to determine the next course of action. Usually, the area will require some work with a tap down device to level any areas that were pulled higher than level. This process may go on for several pulls and taps until the area is as close to level as possible. The do-it-yourself-er doesn't get a reflective source, tap down or training in how to use each of these items and more often than not makes the once small door ding a variable mess when finally deciding to throw in the towel. The suction cup is simply ineffective.

Damage very large and gradual may actually move with a strong enough suction and it may actually look somewhat better than the original dent, but it effectively "locks" the metal into place and the distortions or buckles around the area that have not been properly removed before addressing the main low areas of the dent are now cementing everything into place. The remaining topic (and my favorite) dry ice and a hair dryer seems to get rave reviews on you-tube and the like. Unfortunately this once again doesn't address the buckles and only sometimes removes a portion of the dent.

The main down side to this method is the process it uses. Dry ice or the "computer duster" propellant will rapidly cool the substrate and paint. The hair dryer is then used to rapidly bring the panel temp. above 150 degrees F. The rapid contraction and subsequent expansion of the substrate is what actually makes the dent pop but what's happening on a much smaller level is paint damage. The paint is almost always micro-fractured which leads to paint cracking, peeling and corrosion. Much of this damage will not be seen for several months down the road when the elements have had time to breach the fractures and make them worse.

One PDR company is as good as another, Right?

All dent companies are not created equal and actually let me expand on that by saying all pdr technicians are not created equally. One of the main reasons for the boom in pdr company growth is the "claim to fame" or "gold rush" mentality. We've all seen the commercials for get rich quick schemes. Some very talented technicians have and still do make a very good living repairing dents. Most earn moderate incomes that do not carry bragging rights though. Every Tom, Dick and Harry tired of their 9-5 job learns about the alleged 6 figure income made by pdr technicians and heads out for two weeks of training at a mis-information factory such as Ding King or Right Look and thinks they will set the world on fire directly thereafter. In reality they spend two (or even one) weeks learning little about real world dents and almost always pick up bad habits that will doom them from ever being able to repair a dent properly.

The "Mills",as they are affectionately referred to in the industry, also sell the aspiring technician a "package" deal complete with every tool needed to repair any dent out there. Unfortunately what they are actually getting is the cheapest set of Chinese made coat hangers good money can buy. The aspiring technician returns home after training and (after being told they are ready) begins selling their service. The problem being they often cannot see the dent properly to repair it and do not have the acquired skill set to fix the smallest of dings. The end result is a moderate improvement with high spots throughout the dent and even cracked paint. The technician either continues on frustrated, trying to do better (or not if they don't care enough about the quality) or will lower prices justifying to themselves that a lower quality repair is still worth something.

And more still will throw in the towel all together after making such a bad name for themselves that they can no longer find work. This surge of low end "technicians" has led to a misconception that PDR is an inferior repair process as compared to a body shop. In fact, this conception is true when it pertains to someone performing such gross butchery. The general rule of thumb for a PROFESSIONAL Paintless Dent Repair is that it should cost between 1/2 to 1/3 that of a conventional body shop repair. Professional technicians have spend many hundreds, if not thousands, of hours perfecting their craft and don't sell themselves short. If you find yourself shopping for the best deal (lets face it, in this economy who doesn't) be leery of a rock bottom price. More often than not you WILL get what you pay for and will end up wishing you had paid a little more when rust starts to appear where the dent was, due to the hack cracking your vehicles paint!

To learn more about PDR and find the answers to common PDR questions visit our site http://dentsvanish.com

Loveland  

Auto Body Paintless Dent Repair (PDR)

Dent Removal Cost

COLORADO Paintless dent repair light

Lafayette Pop a Dent

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Lafayette .

Paintless Dent Repair Process

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Dent Removal Cost

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Pop a Dent

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Lafayette  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Auto Dent Repair

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Auto Dent Repair

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Removal

Lafayette

About Paintless Dent Repair

Owing to the reasons that paintless dent repair is fast and efficient it is quickly becoming popular. But there is a dearth of trained professional technicians who are skilled in the techniques that are required for this trade. If after training you want to start your own business then here are some tips to keep in mind when starting your Paintless Dent Repair (PDR) Business.

1. Survey the Market:

It is very important that you consider your potential market. Decide who you will work with? Do you have any connections at a body repair shop, wholesalers, car dealer, detail shop, service centre, etc who will hire you once you complete your paintless dent removal course?

2. Survey your Competition:

Collect information about how many paintless dent removal technicians there are in your area and how are they operating in your potential market. What are the charges for their services and what kind of a relation does your competition have with your potential market as well. Note all these things down for reference.

3. Register your Business:

Check out your state government's website and get information about how to register your business. Make sure that you choose a business name that connects you to the paintless dent repair industry and you could even use the words like dents, dings, dent repair, etc. Complete the entire registration process or even get some professional help.

4. What are your State's Requirements?

The rules and regulations vary from state to state and so it is important that you are completely aware of all the requirements for setting up a PDR Business. You may need business insurance, sales license, shop space, etc. You could ask a local dealer or the office manager of a PDR company what their dealers require from their vendors that is you.

5. Get Trained and buy the Tools:

You need to get trained at a very good academy so that you are well versed in the techniques and skills required in this business. You could consider the name Dents R Us for your paintless dent removing training. For more info check them out at http://www.dentsrus.com.au. You will also need to buy your tools for the job and you need to practice as much as possible.

6. Get Business Material:

You will need office stationery, business cards, invoices, etc and even some accounting material.

7. Don't quit your Current Job!

It is important that you keep your current job as you will need some income to support the business and the family till you are really on your way.

8. Practice on your Acquaintances:

As you begin your business you will need as much practice as you can get and one of the best ways is to practice with the cars belonging to your connections and acquaintances. Of course not many people will hand over the keys to their BMWs, until you are sure of your skills but till then you can even ask your local body shop to give you some work for no pay.

9. Pitch yourself:

You need to be your best marketing strategy. You need to start talking about your work to potential clients or people who will get you work. You need to show them what you are capable of and you need to convince them that you are only getting better and it is YOU that is working for them. Be responsible and you will get recommendations.

10. Legalities:

Last but not the least, finalise your legal businesses and tie up the loose ends in regards to conducting your business as a vendor to body shops to dealerships.

These are few things you could keep in your mind when starting out. Hopefully they have been of some help.

Paintless dent repair light

It happens to the best of us. You know that dent or ding that you notice as you're washing your car. You think to yourself "where did that come from?" Then you shake your head in disappointment. This happens to one in three people. So, what can you do about it?

You first need to take action in preventing the dents from happening in the first place or happening again. What you should try to do is try parking your car farther out or in an area where fewer cars are parked to avoid getting the dents or dings. There are people out there who haphazardly swing their doors open, not to mention the amount of kids who do that too. Also making sure not to park near a cart return spot can reduce your chances of such incidents. Shopping carts are a common culprit in denting cars! Parking a little farther would also provide you the chance to get a little exercise in your daily routine. It is a win-win step to preventing dents!

So now you may be wondering why you should even bother fixing those little dents on your car. For some people self image or self reflection of their car will be a reason to fix minor dents and dings. They feel that their car is a reflection of them and they want it to look its best and make a good impression. Some people will want to fix it solely because they wanted to preserve the value of their car. Another huge reason is that it takes away from the value of your car. When and if you decide to sell or trade in your car that will be a factor in how much you get for your car! Either reason is perfectly sound. The reality is that even though most people want to fix or repair their car they think it will cost too much money and also may take too much time. So what is a solution to this problem?

The best solution is PDR or Paintless Dent Removal. Paintless Dent Removal is a process in which tools, rods and reflective light sources are used to remove dings and dents. This is a very effective process if your paint has not been cracked. The dent is carefully and craftily massaged out from the inside. Dents--from the size of a dime to 2 or 3 inches in diameter and larger--disappear in a span of five to 15 minutes. In many cases, there is no evidence a dent ever existed. This is a great option since no bonding agent or paint is needed. It can often be difficult and time consuming to match paint colors. Also it will save you money since fewer supplies are involved in the process. The best thing about Paintless Dent Removal is that it does not take away of the value your car. Also keep in mind that Paintless Dent Removal can be completed in a short time. So you will not be very long with out your vehicle. This is a great option for anyone no matter what your reason may be for fixing the dents on your car!

Lafayette  

About Paintless Dent Repair

Paintless dent repair crease

COLORADO Paintless dent repair light

COLORADO Paintless Dent Repair at Home

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in COLORADO .

Paintless Dent Removal Cost

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Pop a Dent

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Car Dent Repair

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in COLORADO  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Dent Repair Cost

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless dent repair light

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless dent repair light

COLORADO

What You Need To Know About Dents

Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?

Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.

Why the popularity

PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.

The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.

The car does not need re-spraying and this brings down your overall costs.

Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.

Is paintless dent removal for you?

As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.

PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.

The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.

Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.

Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.

Auto Dent Repair

Owing to the reasons that paintless dent repair is fast and efficient it is quickly becoming popular. But there is a dearth of trained professional technicians who are skilled in the techniques that are required for this trade. If after training you want to start your own business then here are some tips to keep in mind when starting your Paintless Dent Repair (PDR) Business.

1. Survey the Market:

It is very important that you consider your potential market. Decide who you will work with? Do you have any connections at a body repair shop, wholesalers, car dealer, detail shop, service centre, etc who will hire you once you complete your paintless dent removal course?

2. Survey your Competition:

Collect information about how many paintless dent removal technicians there are in your area and how are they operating in your potential market. What are the charges for their services and what kind of a relation does your competition have with your potential market as well. Note all these things down for reference.

3. Register your Business:

Check out your state government's website and get information about how to register your business. Make sure that you choose a business name that connects you to the paintless dent repair industry and you could even use the words like dents, dings, dent repair, etc. Complete the entire registration process or even get some professional help.

4. What are your State's Requirements?

The rules and regulations vary from state to state and so it is important that you are completely aware of all the requirements for setting up a PDR Business. You may need business insurance, sales license, shop space, etc. You could ask a local dealer or the office manager of a PDR company what their dealers require from their vendors that is you.

5. Get Trained and buy the Tools:

You need to get trained at a very good academy so that you are well versed in the techniques and skills required in this business. You could consider the name Dents R Us for your paintless dent removing training. For more info check them out at http://www.dentsrus.com.au. You will also need to buy your tools for the job and you need to practice as much as possible.

6. Get Business Material:

You will need office stationery, business cards, invoices, etc and even some accounting material.

7. Don't quit your Current Job!

It is important that you keep your current job as you will need some income to support the business and the family till you are really on your way.

8. Practice on your Acquaintances:

As you begin your business you will need as much practice as you can get and one of the best ways is to practice with the cars belonging to your connections and acquaintances. Of course not many people will hand over the keys to their BMWs, until you are sure of your skills but till then you can even ask your local body shop to give you some work for no pay.

9. Pitch yourself:

You need to be your best marketing strategy. You need to start talking about your work to potential clients or people who will get you work. You need to show them what you are capable of and you need to convince them that you are only getting better and it is YOU that is working for them. Be responsible and you will get recommendations.

10. Legalities:

Last but not the least, finalise your legal businesses and tie up the loose ends in regards to conducting your business as a vendor to body shops to dealerships.

These are few things you could keep in your mind when starting out. Hopefully they have been of some help.

COLORADO  

Paintless Dent Removal - How to Handle Dents

Car Dent Repair

COLORADO Paintless dent repair light

Broomfield Paintless Dent Repair Process

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Broomfield .

Paintless Dent Repair Course

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Pop a Dent

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Car Dent Remover

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Broomfield  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless dent repair light

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless dent repair crease

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Removal Cost

Broomfield

Paintless Dent Removal - Is It A Good Choice?

The long arm of car repair insurance doesn't stop at extended warranties or tire road hazard insurance. Marketing gurus have found all sorts of knick knacks to insure. Among the top are ding and dent protection plans. Ding and dent insurance is growing steadily, and addresses those unsightly shopping cart and parking lot dings.

Dings and dents are fairly synonymous terms, although a ding is smaller than a dent. You'll notice a dent. You'll need to squint, or catch the vehicle in the right angle or sunlight to see a ding. Some dings are smaller than eraser heads.

Like extended warranties or tire insurance, dent and ding protection plans promise to pay for damages in part or in full for a specific period of time. These plans are primarily sold by new car dealerships and cost a few hundred dollars.

Ding and Dent Repair: Paintless Dent Repair

Ding and dent repair is called PDR, short for Paintless Dent Repair. There are many companies that perform this service: Ding Doctor, Ding King, No Dents, Dent Wizard...the list goes on. Some are better then others, although ultimately it's up to the skill of the PDR technician. Prices are similar.

How is it done?

Most PDR techniques are non-intrusive. The PDR technicians use specially designed tools and gadgets to slip behind the damaged panels and manipulate and massage the damaged metal back to its original form.

Does it work?

Actually, it's incredible! It works so well that in the majority of cases the dings and dents are completely removed. They're invisible, gone, can't-believe-your-eyes fixed.

I saw a soccer-ball-sized dent removed from the rear fender of a $120,000 car. The dent also had a large crease, which makes repairs even harder. After thirty minutes there was no visible detection that a dent was ever there. The repair cost the client $400. Traditional body shop estimates were hovering at $2700.

PDR positives

  • Very low cost compared to traditional body shops
  • Same day repairs--even while-you-wait service
  • No paint work, sanding, or traditional bodywork required
  • Original paint remains--helps retain vehicles looks and value
  • Body panels remain intact--maintaining structural integrity
PDR negatives

  • PDR does not address scratches or paint chips that are often associated with dings (Many PDR companies will address chips and scratches, but it's not PDR technology)
  • Many areas of body panels are not accessible, so PDR is not an option
  • Plastic bumpers or any plastic components can't be fixed with PDR techniques. Since the bumper is the most common area to get damaged, this is a significant downside of PDR technology.
  • Some damage can occur to door panels, paint, interiors, window glass and hardware, although damage of any kind is rare.
Do you need PDR insurance?

God, no!

Should you get your dings fixed using PDR techniques?

Hell, yes!

Let me explain...

Insuring against dings and dents does not make economic sense. Ding repairs average around $50 per ding. Some dings cost $99 to $149 to repair. Two to four dings can run $100 to $450, depending on the size of the dent. Insurance at this level is just not necessary. Moreover, it's a gamble you will lose.

To benefit from a $300, two-year plan, your vehicle would need to sustain multiple "PDR repairable" dings or dents. Despite your coverage, you may not even notice the dings, making a claim impossible. Also, despite the amazing PDR techniques, they can't fix everything, especially the chips and scratches that so frequently accompany a ding--should dings even occur.

Yes, get your dings fixed with PDR (if they're bothering you), but don't buy an insurance plan.

Protection plan economics 101

An article by Terence O'Hara in the Washington Post is a wonderful piece on the insanity of protection plans, and is applicable here. He writes:

The decision to buy an extended warranty...defies the recommendations of economists, consumer advocates and product quality experts, who all warn that the plans rarely benefit consumers and are nearly always a waste of money.

'[Extended warranties and protection plans] make no rational sense,' Harvard economist David Cutler said. 'The implied probability [of an issue] has to be substantially greater than the risk that you can't afford to fix it or replace it. If you're buying a $400 item, for the overwhelming number of consumers that level of spending is not a risk you need to insure under any circumstances.'

...extended warranties play upon a basic human trait to avoid loss, even if it means sacrificing a possible future gain. In this case, the gain is all the other things of value that a consumer could buy with the money that was spent on a warranty

Fix your dings

Fix your dings and dents (if you want) as they come--maybe every spring. Fixing dings keeps your car looking pristine, and increases its value. But don't bother with a protection plan. Save your money.

Hold off on that paint job

Quality paintless dent repair is often a great substitute for those considering full paint jobs. Whenever possible, it's best to keep the original paint. Good PDR combined with a professional detail can restore vehicles to show room condition for less than $500.

Go with the best

Since 1983 Dent Wizard has been pioneering PDR technology. Their PDR technicians undergo extensive and ongoing training. The rates are reasonable and the quality is excellent. Always request a master PDR technician, as there are various levels of abilities.

Check with local dealers

Dealerships in your area may offer Dent Wizard. Your vehicle does not have to be of the same make as the dealership. In other words, you can bring your Chevy to a Ford dealer for PDR work.

Myths

Do it yourself paintless dent repair is easy.

No it 's not. It requires training, skill, and experience. There are many who practice PDR techniques who crack or flake the paint, or who create ripples in the metal.

The PDR products sold on TV do the same thing.

No! Not even close. There's no good substitute for the art of PDR.

Scratch and dent repair are the same thing.

No. A ding is a small dent, which can often be repaired via paintless dent repair procedures. A scratch is an actual break in the surface of the clear coat or paint, requiring traditional body shop techniques, or touch up paint.

It's easy to learn how to repair dents on cars.

Maybe for some, but it's a skill that few master. Dent Wizard offers a great training program. The management and staff are top notch.

What's the best car dent removing protection plan?

Money in your bank account!

Paintless Dent Repair at Home

Your Situation

We have all been there. Miss-judged the size of a parking space and subsequently dented your car, come back from shopping center to find a dent. Or maybe somebody has pulled out on you and dented the side of the vehicle. Whatever the situation, the resulting dents and dings to the bodywork are a pain and they need sorting, quickly. Most importantly, you want them fixed cheaply and without affecting your insurance premium.

Well this is where Auto Body Paintless Dent Repair (PDR) specialists come in with their handy Mobile dent repair services. But what exactly is (PDR)?

Auto Body Paintless Dent Repair (PDR) is essentially the removal of dents from a vehicle body where the paint is not damaged, whoever this type of repair is also a great way to save money even with damaged paintwork. There are several methods, but a popular choice involves the use of special rods and picks. The rods and picks are used to literally massage the dent from inside of the body panel. An alternative PDR method is the application of glue to the outside of the body panel. The glue then allows for the dents to be pulled out. Mobile Auto Body Paintless Dent Removal is always the best value when you consider your alternative.

Can I do it myself?

PDR for short takes many years to perfect and an amateur repair could cause more harm than good to your vehicle. With Auto Body Paintless Dent Repair (PDR) it is important to ensure that the original paint finish is kept in tact and fillers and paint are not required. Therefore the dent technician needs to know exactly what they are doing!

Training can be found in all levels of paintless dent repair from the beginner to the more advanced PDR technician. Great careers can be made all over the nation and around the world and the earning can be great. To find out more about your local Mobile Auto Body Paintless Dent Repair service or PDR Training, just Google the correct keywords and you will be on your way to saving a lot of money by getting shot of those horrible car dents and dings that De-value you vehicle so much. Or better still why not think about training in this sort after car dent repair service and make a long term career for yourself.

So remember... The next time you see nasty looking car dents or dings in you pride and joy, think about calling a Mobile Auto Body Paintless Dent Removal service before claiming on your insurance! Most often, it's cheaper than paying your insurance excess.

Broomfield  

Does PDR Work?

Paintless Dent Removal

COLORADO Paintless dent repair light

Columbine Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Columbine .

Car Dent Remover

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Car Dent Remover

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Pop a Dent

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Columbine  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless Dent Repair Process

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Repair at Home

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair Course

Columbine

Does PDR Work?

Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?

Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.

Why the popularity

PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.

The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.

The car does not need re-spraying and this brings down your overall costs.

Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.

Is paintless dent removal for you?

As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.

PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.

The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.

Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.

Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.

Dent Repair Cost

PDR stands for paintless dent repair. It's a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn't take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops.

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It's a new way of fixing dents and dings that is putting the car repair world at notice!

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Columbine  

What is Paintless Dent Removal?

Paintless Dent Repair Process

COLORADO Paintless dent repair light

Denver Paintless dent repair light

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Denver .

Paintless dent repair light

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Repair at Home

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless Dent Repair at Home

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Denver  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless dent repair light

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Repair Course

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Car Dent Remover

Denver

Paintless Dent Removal Techniques: How To Do It Yourself

PDR stands for paintless dent repair. It's a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn't take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops.

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It's a new way of fixing dents and dings that is putting the car repair world at notice!

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless dent repair light

The long arm of car repair insurance doesn't stop at extended warranties or tire road hazard insurance. Marketing gurus have found all sorts of knick knacks to insure. Among the top are ding and dent protection plans. Ding and dent insurance is growing steadily, and addresses those unsightly shopping cart and parking lot dings.

Dings and dents are fairly synonymous terms, although a ding is smaller than a dent. You'll notice a dent. You'll need to squint, or catch the vehicle in the right angle or sunlight to see a ding. Some dings are smaller than eraser heads.

Like extended warranties or tire insurance, dent and ding protection plans promise to pay for damages in part or in full for a specific period of time. These plans are primarily sold by new car dealerships and cost a few hundred dollars.

Ding and Dent Repair: Paintless Dent Repair

Ding and dent repair is called PDR, short for Paintless Dent Repair. There are many companies that perform this service: Ding Doctor, Ding King, No Dents, Dent Wizard...the list goes on. Some are better then others, although ultimately it's up to the skill of the PDR technician. Prices are similar.

How is it done?

Most PDR techniques are non-intrusive. The PDR technicians use specially designed tools and gadgets to slip behind the damaged panels and manipulate and massage the damaged metal back to its original form.

Does it work?

Actually, it's incredible! It works so well that in the majority of cases the dings and dents are completely removed. They're invisible, gone, can't-believe-your-eyes fixed.

I saw a soccer-ball-sized dent removed from the rear fender of a $120,000 car. The dent also had a large crease, which makes repairs even harder. After thirty minutes there was no visible detection that a dent was ever there. The repair cost the client $400. Traditional body shop estimates were hovering at $2700.

PDR positives

  • Very low cost compared to traditional body shops
  • Same day repairs--even while-you-wait service
  • No paint work, sanding, or traditional bodywork required
  • Original paint remains--helps retain vehicles looks and value
  • Body panels remain intact--maintaining structural integrity
PDR negatives

  • PDR does not address scratches or paint chips that are often associated with dings (Many PDR companies will address chips and scratches, but it's not PDR technology)
  • Many areas of body panels are not accessible, so PDR is not an option
  • Plastic bumpers or any plastic components can't be fixed with PDR techniques. Since the bumper is the most common area to get damaged, this is a significant downside of PDR technology.
  • Some damage can occur to door panels, paint, interiors, window glass and hardware, although damage of any kind is rare.
Do you need PDR insurance?

God, no!

Should you get your dings fixed using PDR techniques?

Hell, yes!

Let me explain...

Insuring against dings and dents does not make economic sense. Ding repairs average around $50 per ding. Some dings cost $99 to $149 to repair. Two to four dings can run $100 to $450, depending on the size of the dent. Insurance at this level is just not necessary. Moreover, it's a gamble you will lose.

To benefit from a $300, two-year plan, your vehicle would need to sustain multiple "PDR repairable" dings or dents. Despite your coverage, you may not even notice the dings, making a claim impossible. Also, despite the amazing PDR techniques, they can't fix everything, especially the chips and scratches that so frequently accompany a ding--should dings even occur.

Yes, get your dings fixed with PDR (if they're bothering you), but don't buy an insurance plan.

Protection plan economics 101

An article by Terence O'Hara in the Washington Post is a wonderful piece on the insanity of protection plans, and is applicable here. He writes:

The decision to buy an extended warranty...defies the recommendations of economists, consumer advocates and product quality experts, who all warn that the plans rarely benefit consumers and are nearly always a waste of money.

'[Extended warranties and protection plans] make no rational sense,' Harvard economist David Cutler said. 'The implied probability [of an issue] has to be substantially greater than the risk that you can't afford to fix it or replace it. If you're buying a $400 item, for the overwhelming number of consumers that level of spending is not a risk you need to insure under any circumstances.'

...extended warranties play upon a basic human trait to avoid loss, even if it means sacrificing a possible future gain. In this case, the gain is all the other things of value that a consumer could buy with the money that was spent on a warranty

Fix your dings

Fix your dings and dents (if you want) as they come--maybe every spring. Fixing dings keeps your car looking pristine, and increases its value. But don't bother with a protection plan. Save your money.

Hold off on that paint job

Quality paintless dent repair is often a great substitute for those considering full paint jobs. Whenever possible, it's best to keep the original paint. Good PDR combined with a professional detail can restore vehicles to show room condition for less than $500.

Go with the best

Since 1983 Dent Wizard has been pioneering PDR technology. Their PDR technicians undergo extensive and ongoing training. The rates are reasonable and the quality is excellent. Always request a master PDR technician, as there are various levels of abilities.

Check with local dealers

Dealerships in your area may offer Dent Wizard. Your vehicle does not have to be of the same make as the dealership. In other words, you can bring your Chevy to a Ford dealer for PDR work.

Myths

Do it yourself paintless dent repair is easy.

No it 's not. It requires training, skill, and experience. There are many who practice PDR techniques who crack or flake the paint, or who create ripples in the metal.

The PDR products sold on TV do the same thing.

No! Not even close. There's no good substitute for the art of PDR.

Scratch and dent repair are the same thing.

No. A ding is a small dent, which can often be repaired via paintless dent repair procedures. A scratch is an actual break in the surface of the clear coat or paint, requiring traditional body shop techniques, or touch up paint.

It's easy to learn how to repair dents on cars.

Maybe for some, but it's a skill that few master. Dent Wizard offers a great training program. The management and staff are top notch.

What's the best car dent removing protection plan?

Money in your bank account!

Denver  

Paintless Dent Removal - How to Handle Dents

Paintless Dent Repair Process

COLORADO Paintless dent repair light

Grand Junction Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Grand Junction .

Auto Dent Repair

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Removal

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless Dent Repair Course

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Grand Junction  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless dent repair light

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Repair Course

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair Course

Grand Junction

Auto Hail Damage Repair

Your Situation

We have all been there. Miss-judged the size of a parking space and subsequently dented your car, come back from shopping center to find a dent. Or maybe somebody has pulled out on you and dented the side of the vehicle. Whatever the situation, the resulting dents and dings to the bodywork are a pain and they need sorting, quickly. Most importantly, you want them fixed cheaply and without affecting your insurance premium.

Well this is where Auto Body Paintless Dent Repair (PDR) specialists come in with their handy Mobile dent repair services. But what exactly is (PDR)?

Auto Body Paintless Dent Repair (PDR) is essentially the removal of dents from a vehicle body where the paint is not damaged, whoever this type of repair is also a great way to save money even with damaged paintwork. There are several methods, but a popular choice involves the use of special rods and picks. The rods and picks are used to literally massage the dent from inside of the body panel. An alternative PDR method is the application of glue to the outside of the body panel. The glue then allows for the dents to be pulled out. Mobile Auto Body Paintless Dent Removal is always the best value when you consider your alternative.

Can I do it myself?

PDR for short takes many years to perfect and an amateur repair could cause more harm than good to your vehicle. With Auto Body Paintless Dent Repair (PDR) it is important to ensure that the original paint finish is kept in tact and fillers and paint are not required. Therefore the dent technician needs to know exactly what they are doing!

Training can be found in all levels of paintless dent repair from the beginner to the more advanced PDR technician. Great careers can be made all over the nation and around the world and the earning can be great. To find out more about your local Mobile Auto Body Paintless Dent Repair service or PDR Training, just Google the correct keywords and you will be on your way to saving a lot of money by getting shot of those horrible car dents and dings that De-value you vehicle so much. Or better still why not think about training in this sort after car dent repair service and make a long term career for yourself.

So remember... The next time you see nasty looking car dents or dings in you pride and joy, think about calling a Mobile Auto Body Paintless Dent Removal service before claiming on your insurance! Most often, it's cheaper than paying your insurance excess.

Paintless Dent Repair at Home

Paintless dent removing is increasingly becoming popular day by day as it is not only a time saving technique, but is also cost effective and efficient. These techniques are the best solution for minor dents and actually result in your car looking brand new. Even a trained eye will not be able to detect where the dented area was.

One of the most common reasons why PDR is used is to repair hail damage, minor body creases, door dings and minor bumper indentions. This technique can also be used to help prepare the damaged panel for paint repair. In such cases it is referred to as push-to-paint or push-for-paint. One of the limiting factors that ails PDR is that it cannot be used for paint repair and the amount of metal that can be stretched by the incurred damage. And so many times sharp dents and creases may not be repairable at least not without a paint job.

In the recent years there has been a conscious effort to bring a standard to this trade and even The National Alliance of Paintless Dent Repair Technicians (NAPDRT) was formed in 2006. The mission of this organization is to educate consumers and to enhance the industry standards through third party certification and mutual accountability. To date however there is no industry wide certification process in the field of Paintless Dent Repairs.

Methods of Repair:
One of the most common methods of paintless dent repair is to utilise body picks and metal rods to push the dent out from the inner side of the panel that is being repaired. Also glue might be used from the exterior of the panel in order to pull the dents out. In either of the cases fine tuning of these repairs requires "tapping" down the repair in order to remove the small high spots so as to make the surface flat. PDR may use both steel and aluminum panels.

Fluorescent lighting or in some cases even light reflection boards are used to see the shadows that are created by the deformation of the dent. This is an extremely important aspect of the repair process as without the paintless dent repair light or the reflector board the fine detail of the process is unseen and the technician then cannot choose their tool specifically and repair the damage effectively.

The process of paintless dent repair needs the technician to specifically push the metal in the exact location to a precise height which can be seen or witnessed with a PDR reading instrument such as the PDR reflector board or the PDR light.

This trade needs some special PDR training which can be availed at a number of schools Australia wide. But if you are interested in the best then head down to Dents R Us. For more info please visit http://www.dentsrus.com.au.

Grand Junction  

10 Things to Consider When Starting Your PDR Business

Paintless Dent Repair at Home

COLORADO Paintless dent repair light