KANSAS Hail Damage Repair

Paintless Dent Repair or PDR is a group of procedures used in KANSAS for fixing little dents and dings from the body of cars, buses and vans. A variety damages can be repaired through the paintless dent repair method. Some of the common repair types of damage include stone dents and bumper repair.

Car Dent Remover

The methodologies for paintless dent repair utilize body picks and metal rods to push the damages out from the inner side of the body panel being repaired. A special kind of adhesive may also be used on the external side of panel to pull the dents out. In both the instances, fine-tuning of the dent removal usually involves “tapping” down the ding to take away small spots, making the surface flat and shiny.

The technicians access the dent from window openings, by taking out headlights and tail lights and through wheel well openings. After getting access to the inside surface of the body work, gentle pressure is applied until the dent is removed. Since PDR works from behind the vehicle’s damage, no sanding or putty work are required. Paintless dent repair is used on both aluminum and steel panels. In KANSAS skilled dent repair Techs removes up to 100 per cent of the damage using specially devised PDR procedures. These tools and procedures provide a large range of flexibility and rigidity, with tips tapered and configured to allow for repair to any kind of damage on any type of vehicle. Once the repairs are completed there is no visible or apparent support that a dent was ever there.

Paintless dent repair crease

Some of the great benefits of Paintless Dent Repair are:

• There is no repainting or body filler used.

• It proves to be less expensive than standard body repair.

• The service is done within a few hours.

• The issue of paint over-spray on other areas of vehicle is eliminated.

• There is no risk of color mismatch.

• The vehicle retains its original paint.

A vehicle with showroom paint usually carries a better value than a repainted vehicle. Even if it is just a door or the fender, it is always smart to maintain the original paint as long as possible.

Dent Repair shops based in KANSAS offer expertise for the professional quality of paintless dent removal and scratch repair. Plastic Bumper Repair, automobile scratch and stone chip repairs and hail ding repairs are a few other services that can also be supplied. The paintless dent repair method used by these shops preserves the vehicle value as it maintains the original paintwork.

Paintless Dent Repair at Home

Auto Hail Damage Repair

It can be frightening when you get stuck in a hail storm but the truly scary part is what it can do to your car. You wouldn't think that little chunks of ice could do much damage to sheet metal. However, many people have been left with a car that looks like a golf ball after a nasty winter storm. Auto Hail Damage Repair has changed a lot over the years and can be done in some cases without the need for a new paint job.

For years the standard way to remove dents was by pulling the dent out. You would have to drill holes into the dented area and use a tool to pull the metal back into shape. Then you would have to grind the holes down and use a body filler to smooth them over. After that you would repaint the damaged area and that is one of the biggest drawbacks to this procedure. A paint job that was put on by the manufacturer is of extremely high quality. It is nearly impossible to duplicate it without taking it back to the manufacturer. So you would be left with a section of car that was obviously repainted with inferior materials.

Paintless Dent Repair was invented specifically for this reason. The Mercedes-Benz Company in Germany was having a lot of trouble shipping their cars to the various dealers. When they arrived they would have dents and dings but the car lot would not have the resources to give them a manufacturer quality paint job after they were repaired. So they developed a procedure for Paintless Dent Removal that uses rods to push the dent out from the inside while gently tapping the outside with a hammer. It is important that the technician be very skilled using Paintless Dent Repair techniques because if they strike the metal too hard it will split. Sometimes glue is used on the outside of the car to pull the dent instead of pushing with rods which can eliminate the need for using a hammer on the metal. The only times that Paintless Dent Removal is not possible is if the paint was damaged by the initial impact or if the metal has been stretched too far out of shape.

Paintless Dent Repair is a great way to save money and retain your original manufacturer paint job. Just make sure that the repair shop that you choose is reputable and has done it many times before. To find a local repair shop you can search the internet for Paintless Dent Repair North Georgia.


KANSAS Car Dent Remover

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in KANSAS .

Car Dent Remover

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless dent repair crease

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless Dent Repair Training

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in KANSAS  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless dent repair light

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless dent repair crease

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Pop a Dent

KANSAS

Paintless Dent Repair: Myths and Facts About Car Dent Repair and Insurance

If you get dents in your car your initial reaction is to be shocked, the next reaction is to get angry and the third reaction is to calm down and take the necessary steps to fix the issue. But, when it comes to fixing the issue, are you fixing it in the proper manner? In other words, are you still keeping to long established methods of fixing a dent as opposed to taking advantage of the far more cost effective process of paintless dent repair?

When something novel comes along there will be those people who will move at the opportunity to use the innovations that new methods have to offer. Then again, there will be those people who may not like trying something new simply because they are more familiar with an original process they are familiar. (This is why some people still buy videos and will not to upgrade to DVD.) While this gripping on to the old may seem rather gracious, it can also prove to be a waster of time and extremely expensive. One such example of this can be found in the car world in the form of sticking with traditional bodywork as opposed to paintless dent repair.

For those not familiar with paintless dent repair it references a method when a dent is molded into the car's original form without the requirement of repainting the car. Now, this may seem like a radical diversion from the usual process of fixing and repainting a dent. Obviously, that's because it is! It is also a much more cost effective process of repair as it eliminates the extra costs involved with repainting the finish of an automobile. Yes there is the possibility for a number of unplanned expenses associated with the repainting of a car's finish. In some instances, the new finish may not match the old finish and this can lead to a notable devaluing of the car. (Envision paying a ton of cash in repairs and finishing up making the car's trade in value go down!) As many understand, the possible expenses involved with refinishing the paint on a car can be huge so why not consider paintless dent repair and skip this step?

Once again, the issue is commonly an observance to tradition. That is, car repairs become a member of the "this is the way we always did it and this is the way we will continue to do it" methodology. However, if most people prescribed to this thought pattern we would not be driving automobiles...we would be riding around on horses! Sure, paintless dent repair may look like a radical deviation from what was done before but it is a valuable process that is a much more cost effective improvement over the bigger task methods of the past. As a result of this paintless dent repair is a much wiser solution for your minor repair needs. After all, it is a sensible method that is free of a number of the common nuances involved with old fashioned repair work. Clearly, that is a better module to choose.

Pop a Dent

Paintless dent removal is a good idea for those who have minor dents or dings they want to remove from their vehicle. It doesn't require major body work, and in most cases you can have your car back in as little as a day as opposed to several days to weeks with major body work. The cost is also much lower since the overhead is lower. There are some instances where paintless dent removal isn't possible. If you have a simple dent you want to have pulled out, here are a few things to consider.

How It Works

A technician that has been trained to use specialized tools will work on the dent locally. This means a dented door doesn't need to be removed. In most cases they will access the dent from the other side by going through a window opening or removing the door panel. The dent is then worked on from the inside, and pressed back out. It sounds simple, but it requires skill and patience. The technician needs to have experience in this so that they don't push the dent out too far or damage the surrounding paint. It is something you can do at home, but it's not suggested.

When Paintless Dent Removal is Feasible

Even large dents can be fixed with this method as long as the paint has not been shattered or cracked. If you have had previous body damage repaired in the area, this method may not work. Dents that are close to the edge of a panel are also difficult to repair with this method. The most common application for this method is door dents, dents on the hood or trunk, and dents on the roof. Hail damage can be repaired with this method, but it's a more lengthy process.

Benefits of Paintless Dent Removal

Paintless dent removal is advantageous for several reasons. For one, it's approved by most insurance companies. This means if you have damage that is covered by your auto insurance, you can get it repaired with this method and get your car back much faster. Since nothing is being replaced or removed, the vehicle will retain its factory value as well. You don't need to report body damage when you sell the vehicle. The dent won't need to be repainted or bonded in any way. When a vehicle is damaged and needs paint touch up on just a small area, it's very hard to match the color. Even if they use a color provided by the manufacturer, this doesn't take in to account the wear and tear the current paint job has, and can still stand out and be very noticeable. The turn around is also much faster. With traditional body repair you may have to relinquish your vehicle to the shop for several days, weeks for larger repairs. Paintless dent removal can be done in just a few hours and you can get your car back on the same day in many cases. Of course you want to call ahead to see what kind of schedule the technicians have, as this could hold up the process a bit. If you have to come out of pocket for the repair you will enjoy savings with paintless dent removal over traditional body work.

KANSAS  

Auto Hail Damage Repair

Paintless Dent Repair Course

KANSAS Hail Damage Repair

Wichita Paintless Dent Repair at Home

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Wichita .

Paintless dent repair crease

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Removal

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless dent repair crease

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Wichita  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless dent repair light

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Removal

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Auto Dent Repair

Wichita

Paintless Dent Repair: Myths and Facts About Car Dent Repair and Insurance

Nowadays, the most popular technique for removing dents in your car is paintless dent removal (PDR). Depending on the degree or level of repair for your car, the techniques used in PDR vary although the basic methods are similar. Special tools will be used for applying PDR in order to straighten out or fix dents. The basic method involves gradual pushing of the metal so that it would return to its proper place. Although PDR involves a slow process, it can produce great results for your car especially when it is done properly. More so, your car paint would not be damaged when PDR is applied.

Special kinds of dent removal tools are used in PDR. Skilled operators use these dent removal tools in order to remove or fix dents on your car. These tools are usually flat and long so that they can reach even small gaps like window slots. More so, these tools are able to slide into place to put pressure on the metal. A long flat tool is used in gaps that are usually behind the panel. A skilled operator will then guide the flat tool to the dent and press it to push the metal back into place. The operator will also handle the flat tool in such a way that it massages the surface where the dent is and moves it back into shape.

Paintless dent removal is highly advantageous regardless if your car has small dents or minor damages. This is because it makes use of special tools that do not damage the paint of your car. More so, it is much cheaper as compared to other methods of dent removal. It provides great outcomes for your car when handled or applied by a skilled operator. Thus, you not only save money but time and effort as well.

Pop a Dent

Your Situation

We have all been there. Miss-judged the size of a parking space and subsequently dented your car, come back from shopping center to find a dent. Or maybe somebody has pulled out on you and dented the side of the vehicle. Whatever the situation, the resulting dents and dings to the bodywork are a pain and they need sorting, quickly. Most importantly, you want them fixed cheaply and without affecting your insurance premium.

Well this is where Auto Body Paintless Dent Repair (PDR) specialists come in with their handy Mobile dent repair services. But what exactly is (PDR)?

Auto Body Paintless Dent Repair (PDR) is essentially the removal of dents from a vehicle body where the paint is not damaged, whoever this type of repair is also a great way to save money even with damaged paintwork. There are several methods, but a popular choice involves the use of special rods and picks. The rods and picks are used to literally massage the dent from inside of the body panel. An alternative PDR method is the application of glue to the outside of the body panel. The glue then allows for the dents to be pulled out. Mobile Auto Body Paintless Dent Removal is always the best value when you consider your alternative.

Can I do it myself?

PDR for short takes many years to perfect and an amateur repair could cause more harm than good to your vehicle. With Auto Body Paintless Dent Repair (PDR) it is important to ensure that the original paint finish is kept in tact and fillers and paint are not required. Therefore the dent technician needs to know exactly what they are doing!

Training can be found in all levels of paintless dent repair from the beginner to the more advanced PDR technician. Great careers can be made all over the nation and around the world and the earning can be great. To find out more about your local Mobile Auto Body Paintless Dent Repair service or PDR Training, just Google the correct keywords and you will be on your way to saving a lot of money by getting shot of those horrible car dents and dings that De-value you vehicle so much. Or better still why not think about training in this sort after car dent repair service and make a long term career for yourself.

So remember... The next time you see nasty looking car dents or dings in you pride and joy, think about calling a Mobile Auto Body Paintless Dent Removal service before claiming on your insurance! Most often, it's cheaper than paying your insurance excess.

Wichita  

Paintless Dent Repair: Myths and Facts About Car Dent Repair and Insurance

Paintless dent repair crease

KANSAS Hail Damage Repair

Olathe Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Olathe .

Paintless dent repair crease

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Auto Dent Removal

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Car Dent Remover

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Olathe  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Hail Damage Repair

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Auto Dent Repair

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair Course

Olathe

Paintless Dent Removal Training

It happens to the best of us. You know that dent or ding that you notice as you're washing your car. You think to yourself "where did that come from?" Then you shake your head in disappointment. This happens to one in three people. So, what can you do about it?

You first need to take action in preventing the dents from happening in the first place or happening again. What you should try to do is try parking your car farther out or in an area where fewer cars are parked to avoid getting the dents or dings. There are people out there who haphazardly swing their doors open, not to mention the amount of kids who do that too. Also making sure not to park near a cart return spot can reduce your chances of such incidents. Shopping carts are a common culprit in denting cars! Parking a little farther would also provide you the chance to get a little exercise in your daily routine. It is a win-win step to preventing dents!

So now you may be wondering why you should even bother fixing those little dents on your car. For some people self image or self reflection of their car will be a reason to fix minor dents and dings. They feel that their car is a reflection of them and they want it to look its best and make a good impression. Some people will want to fix it solely because they wanted to preserve the value of their car. Another huge reason is that it takes away from the value of your car. When and if you decide to sell or trade in your car that will be a factor in how much you get for your car! Either reason is perfectly sound. The reality is that even though most people want to fix or repair their car they think it will cost too much money and also may take too much time. So what is a solution to this problem?

The best solution is PDR or Paintless Dent Removal. Paintless Dent Removal is a process in which tools, rods and reflective light sources are used to remove dings and dents. This is a very effective process if your paint has not been cracked. The dent is carefully and craftily massaged out from the inside. Dents--from the size of a dime to 2 or 3 inches in diameter and larger--disappear in a span of five to 15 minutes. In many cases, there is no evidence a dent ever existed. This is a great option since no bonding agent or paint is needed. It can often be difficult and time consuming to match paint colors. Also it will save you money since fewer supplies are involved in the process. The best thing about Paintless Dent Removal is that it does not take away of the value your car. Also keep in mind that Paintless Dent Removal can be completed in a short time. So you will not be very long with out your vehicle. This is a great option for anyone no matter what your reason may be for fixing the dents on your car!

Car Dent Repair

PDR stands for paintless dent repair. It's a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn't take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops.

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It's a new way of fixing dents and dings that is putting the car repair world at notice!

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Olathe  

What is Paintless Dent Removal?

Paintless dent repair crease

KANSAS Hail Damage Repair

Topeka Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Topeka .

Paintless dent repair light

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless dent repair crease

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless dent repair light

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Topeka  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Pop a Dent

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Repair Course

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair Process

Topeka

Auto Hail Damage Repair

If you are a vehicle owner, you have most probably heard of paintless dent repair. It is one of the most widely used techniques for fixing dents and similar types of damage to the car's body. Here you will find useful information about this repair method to help you get a clear idea of when it works best and when to use it.

What is it?

This is a technique used for flattening the dents on the body of a moving vehicle, and more specifically, on the panels. Special metal rods and picks are used to get behind the shell. Then the technician manipulates them to push out the dent. This is how the surface becomes flat once again. One interesting fact about paintless dent repair is that it's been around for over eight decades.

Is it effective for all dents?

The straightforward answer is: no, it isn't, but it's worth looking at the details. As its name suggests, this type of repair technique works only when the paint of the car is intact. If it is damaged, a different method must be used. It is typically more complex and time-consuming. Additionally, when the paint is damaged, time is of the essence for getting the panel restored fully. The good news is that the paint used by modern vehicle manufacturers is highly resistant to cracking, peeling and other types of damage.

Paintless dent repair is most effective for minor dents and creases, hail damage and dings. It would typically work well even if there are multiple dents or creases close together. A close professional inspection of the vehicle's damage is the best way to determine if this technique should be used or not.

Does it matter what material the panel is made from?

This repair method is regarded to be effective and safe for both steel and aluminum panels. It is not known to cause any changes to the structure of these metals that would make them weaker or more susceptible to rust and other types of damage. It is worth noting that with this technique, the paint of the vehicle will remain intact too, provided that it is applied correctly, of course.

Can I do the job it myself?

Theoretically, you can. The tools needed for paintless dent repair are readily available and don't cost a small fortune to buy. There are also plenty of online videos showing you how to apply the technique correctly. Still, if you don't have sufficient knowledge and skill, you risk causing further damage to your vehicle. That is why DIY repair is not a very good idea.

How do I choose a professional paintless dent repair service?

Confirm that the technician who will do the job has received specialized training and has sufficient experience. Ask about the warranty provided before hiring the service. Leading providers usually cover their work with a lifetime warranty. In general, you should know that this type of repair job doesn't take a long time to complete so you should expect to get your vehicle fully fixed in days rather than weeks, unless there is a waiting list.

Dent Repair Cost

So you just got this fabulous new car. It is everything you could want and more. You are so excited that you drive your car around to show everyone that you know. It drives smooth as can be and the exterior looks like only a new car can look, perfect! The paint has a high gloss and is blemish free.

You head on home and go to hop out of your car when all of a sudden your door swings into the fire hydrant that resides next to your driveway. You slowly get out of the car cringing and hoping you did not just put a dent in your new car. With one eye closed you asses the damage. Sure enough there is a ding in your newly acquired car. You feel like crying and walk into your house with your head down low.

The excitement you felt about getting a new car has completely diminished. Sure the dent is small and chances are no one will notice it but you notice it.

So now what do you do?

That is where paintless dent removal comes into play. A paintless dent repair is just that. A dent technician will pop the dent out of the body of your car without having to fill the ding and paint it.

That is good news to you for two reasons. The first is that it is fairly inexpensive to have the dent removed (and quick) so you can have your car looking like it just rolled off of the lot in no time. The second is that you do not have to have actual body work done on your new car so you can still boast that you have all factory paint.

Using paintless dent removal is a wonderful way to keep your car looking new regardless of whether you just have one or two small dents or your car has hail damage.

Topeka  

Dent Removal Tools For Your Car

Paintless Dent Repair at Home

KANSAS Hail Damage Repair

Lawrence Auto Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Lawrence .

Car Dent Remover

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Pop a Dent

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Dent Repair Cost

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Lawrence  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Car Dent Remover

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless dent repair light

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Auto Dent Repair

Lawrence

10 Things to Consider When Starting Your PDR Business

If you get dents in your car your initial reaction is to be shocked, the next reaction is to get angry and the third reaction is to calm down and take the necessary steps to fix the issue. But, when it comes to fixing the issue, are you fixing it in the proper manner? In other words, are you still keeping to long established methods of fixing a dent as opposed to taking advantage of the far more cost effective process of paintless dent repair?

When something novel comes along there will be those people who will move at the opportunity to use the innovations that new methods have to offer. Then again, there will be those people who may not like trying something new simply because they are more familiar with an original process they are familiar. (This is why some people still buy videos and will not to upgrade to DVD.) While this gripping on to the old may seem rather gracious, it can also prove to be a waster of time and extremely expensive. One such example of this can be found in the car world in the form of sticking with traditional bodywork as opposed to paintless dent repair.

For those not familiar with paintless dent repair it references a method when a dent is molded into the car's original form without the requirement of repainting the car. Now, this may seem like a radical diversion from the usual process of fixing and repainting a dent. Obviously, that's because it is! It is also a much more cost effective process of repair as it eliminates the extra costs involved with repainting the finish of an automobile. Yes there is the possibility for a number of unplanned expenses associated with the repainting of a car's finish. In some instances, the new finish may not match the old finish and this can lead to a notable devaluing of the car. (Envision paying a ton of cash in repairs and finishing up making the car's trade in value go down!) As many understand, the possible expenses involved with refinishing the paint on a car can be huge so why not consider paintless dent repair and skip this step?

Once again, the issue is commonly an observance to tradition. That is, car repairs become a member of the "this is the way we always did it and this is the way we will continue to do it" methodology. However, if most people prescribed to this thought pattern we would not be driving automobiles...we would be riding around on horses! Sure, paintless dent repair may look like a radical deviation from what was done before but it is a valuable process that is a much more cost effective improvement over the bigger task methods of the past. As a result of this paintless dent repair is a much wiser solution for your minor repair needs. After all, it is a sensible method that is free of a number of the common nuances involved with old fashioned repair work. Clearly, that is a better module to choose.

Dent Removal Cost

Nowadays, the most popular technique for removing dents in your car is paintless dent removal (PDR). Depending on the degree or level of repair for your car, the techniques used in PDR vary although the basic methods are similar. Special tools will be used for applying PDR in order to straighten out or fix dents. The basic method involves gradual pushing of the metal so that it would return to its proper place. Although PDR involves a slow process, it can produce great results for your car especially when it is done properly. More so, your car paint would not be damaged when PDR is applied.

Special kinds of dent removal tools are used in PDR. Skilled operators use these dent removal tools in order to remove or fix dents on your car. These tools are usually flat and long so that they can reach even small gaps like window slots. More so, these tools are able to slide into place to put pressure on the metal. A long flat tool is used in gaps that are usually behind the panel. A skilled operator will then guide the flat tool to the dent and press it to push the metal back into place. The operator will also handle the flat tool in such a way that it massages the surface where the dent is and moves it back into shape.

Paintless dent removal is highly advantageous regardless if your car has small dents or minor damages. This is because it makes use of special tools that do not damage the paint of your car. More so, it is much cheaper as compared to other methods of dent removal. It provides great outcomes for your car when handled or applied by a skilled operator. Thus, you not only save money but time and effort as well.

Lawrence  

Paintless Dent Removal - How to Handle Dents

Car Dent Repair

KANSAS Hail Damage Repair

Shawnee Car Dent Repair

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Shawnee .

Hail Damage Repair

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless Dent Removal

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Pop a Dent

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Shawnee  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Car Dent Remover

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Removal

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Pop a Dent

Shawnee

Paintless Dent Repair - The Truth, Myths and Misconceptions

Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?

Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.

Why the popularity

PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.

The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.

The car does not need re-spraying and this brings down your overall costs.

Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.

Is paintless dent removal for you?

As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.

PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.

The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.

Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.

Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.

Paintless Dent Repair at Home

Paintless dent removing is increasingly becoming popular day by day as it is not only a time saving technique, but is also cost effective and efficient. These techniques are the best solution for minor dents and actually result in your car looking brand new. Even a trained eye will not be able to detect where the dented area was.

One of the most common reasons why PDR is used is to repair hail damage, minor body creases, door dings and minor bumper indentions. This technique can also be used to help prepare the damaged panel for paint repair. In such cases it is referred to as push-to-paint or push-for-paint. One of the limiting factors that ails PDR is that it cannot be used for paint repair and the amount of metal that can be stretched by the incurred damage. And so many times sharp dents and creases may not be repairable at least not without a paint job.

In the recent years there has been a conscious effort to bring a standard to this trade and even The National Alliance of Paintless Dent Repair Technicians (NAPDRT) was formed in 2006. The mission of this organization is to educate consumers and to enhance the industry standards through third party certification and mutual accountability. To date however there is no industry wide certification process in the field of Paintless Dent Repairs.

Methods of Repair:
One of the most common methods of paintless dent repair is to utilise body picks and metal rods to push the dent out from the inner side of the panel that is being repaired. Also glue might be used from the exterior of the panel in order to pull the dents out. In either of the cases fine tuning of these repairs requires "tapping" down the repair in order to remove the small high spots so as to make the surface flat. PDR may use both steel and aluminum panels.

Fluorescent lighting or in some cases even light reflection boards are used to see the shadows that are created by the deformation of the dent. This is an extremely important aspect of the repair process as without the paintless dent repair light or the reflector board the fine detail of the process is unseen and the technician then cannot choose their tool specifically and repair the damage effectively.

The process of paintless dent repair needs the technician to specifically push the metal in the exact location to a precise height which can be seen or witnessed with a PDR reading instrument such as the PDR reflector board or the PDR light.

This trade needs some special PDR training which can be availed at a number of schools Australia wide. But if you are interested in the best then head down to Dents R Us. For more info please visit http://www.dentsrus.com.au.

Shawnee  

Paintless Dent Repair - The Truth, Myths and Misconceptions

Paintless dent repair crease

KANSAS Hail Damage Repair

Manhattan Paintless Dent Removal

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Manhattan .

Paintless dent repair crease

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Paintless dent repair light

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Car Dent Remover

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Manhattan  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless Dent Repair Training

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Pop a Dent

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair at Home

Manhattan

What Is Paintless Dent Removal?

So you just got this fabulous new car. It is everything you could want and more. You are so excited that you drive your car around to show everyone that you know. It drives smooth as can be and the exterior looks like only a new car can look, perfect! The paint has a high gloss and is blemish free.

You head on home and go to hop out of your car when all of a sudden your door swings into the fire hydrant that resides next to your driveway. You slowly get out of the car cringing and hoping you did not just put a dent in your new car. With one eye closed you asses the damage. Sure enough there is a ding in your newly acquired car. You feel like crying and walk into your house with your head down low.

The excitement you felt about getting a new car has completely diminished. Sure the dent is small and chances are no one will notice it but you notice it.

So now what do you do?

That is where paintless dent removal comes into play. A paintless dent repair is just that. A dent technician will pop the dent out of the body of your car without having to fill the ding and paint it.

That is good news to you for two reasons. The first is that it is fairly inexpensive to have the dent removed (and quick) so you can have your car looking like it just rolled off of the lot in no time. The second is that you do not have to have actual body work done on your new car so you can still boast that you have all factory paint.

Using paintless dent removal is a wonderful way to keep your car looking new regardless of whether you just have one or two small dents or your car has hail damage.

Hail Damage Repair

Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?

Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.

Why the popularity

PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.

The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.

The car does not need re-spraying and this brings down your overall costs.

Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.

Is paintless dent removal for you?

As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.

PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.

The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.

Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.

Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.

Manhattan  

Paintless Dent Removal Training

Paintless Dent Removal

KANSAS Hail Damage Repair

Lenexa Auto Dent Repair

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Lenexa .

Paintless dent repair light

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Car Dent Remover

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Paintless Dent Repair Course

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Lenexa  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Car Dent Repair

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Dent Repair Cost

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless dent repair light

Lenexa

About Paintless Dent Repair

If you get dents in your car your initial reaction is to be shocked, the next reaction is to get angry and the third reaction is to calm down and take the necessary steps to fix the issue. But, when it comes to fixing the issue, are you fixing it in the proper manner? In other words, are you still keeping to long established methods of fixing a dent as opposed to taking advantage of the far more cost effective process of paintless dent repair?

When something novel comes along there will be those people who will move at the opportunity to use the innovations that new methods have to offer. Then again, there will be those people who may not like trying something new simply because they are more familiar with an original process they are familiar. (This is why some people still buy videos and will not to upgrade to DVD.) While this gripping on to the old may seem rather gracious, it can also prove to be a waster of time and extremely expensive. One such example of this can be found in the car world in the form of sticking with traditional bodywork as opposed to paintless dent repair.

For those not familiar with paintless dent repair it references a method when a dent is molded into the car's original form without the requirement of repainting the car. Now, this may seem like a radical diversion from the usual process of fixing and repainting a dent. Obviously, that's because it is! It is also a much more cost effective process of repair as it eliminates the extra costs involved with repainting the finish of an automobile. Yes there is the possibility for a number of unplanned expenses associated with the repainting of a car's finish. In some instances, the new finish may not match the old finish and this can lead to a notable devaluing of the car. (Envision paying a ton of cash in repairs and finishing up making the car's trade in value go down!) As many understand, the possible expenses involved with refinishing the paint on a car can be huge so why not consider paintless dent repair and skip this step?

Once again, the issue is commonly an observance to tradition. That is, car repairs become a member of the "this is the way we always did it and this is the way we will continue to do it" methodology. However, if most people prescribed to this thought pattern we would not be driving automobiles...we would be riding around on horses! Sure, paintless dent repair may look like a radical deviation from what was done before but it is a valuable process that is a much more cost effective improvement over the bigger task methods of the past. As a result of this paintless dent repair is a much wiser solution for your minor repair needs. After all, it is a sensible method that is free of a number of the common nuances involved with old fashioned repair work. Clearly, that is a better module to choose.

Paintless dent repair crease

Paintless Dent Repair or PDR is a group of procedures used for fixing little dents and dings from the body of cars, buses and vans. A variety damages can be repaired through the paintless dent repair method. Some of the common repair types of damage include stone dents and bumper repair.

The methodologies for paintless dent repair utilize body picks and metal rods to push the damages out from the inner side of the body panel being repaired. A special kind of adhesive may also be used on the external side of panel to pull the dents out. In both the instances, fine-tuning of the dent removal usually involves "tapping" down the ding to take away small spots, making the surface flat and shiny.

The technicians access the dent from window openings, by taking out headlights and tail lights and through wheel well openings. After getting access to the inside surface of the body work, gentle pressure is applied until the dent is removed. Since PDR works from behind the vehicle's damage, no sanding or putty work are required. Paintless dent repair is used on both aluminum and steel panels. A skilled dent repair repairer removes up to 100 per cent of the damage using specially devised PDR procedures. These tools and procedures provide a large range of flexibility and rigidity, with tips tapered and configured to allow for repair to any kind of damage on any type of vehicle. Once the repairs are completed there is no visible or apparent support that a dent was ever there.

Some of the great benefits of Paintless Dent Repair are:

• There is no repainting or body filler used.
• It proves to be less expensive than standard body repair.
• The service is done within a few hours.
• The issue of paint over-spray on other areas of vehicle is eliminated.
• There is no risk of color mismatch.
• The vehicle retains its original paint.

A vehicle with showroom paint usually carries a better value than a repainted vehicle. Even if it is just a door or the fender, it is always smart to maintain the original paint as long as possible.

Dent Clinic based in Sydney, New South Wales Australia offers its expertise for the professional quality of paintless dent removal and scratch repair. Plastic Bumper Repair, automobile scratch and stone chip repairs and hail ding repairs are a few other services that can also be supplied at the Dent Clinic. The paintless dent repair method used by them preserves the vehicle value as it maintains the original paintwork. The professionals at Dent Clinic always assess the damage in detail and honestly to inform the customers about the likely results, post repair. For most satisfactory results in dent repair and removal, you can trust the Dent Clinic.

Lenexa  

Paintless Dent Removal Techniques: How To Do It Yourself

Pop a Dent

KANSAS Hail Damage Repair

Salina Dent Removal Cost

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Salina .

Car Dent Remover

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Car Dent Remover

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Car Dent Remover

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Salina  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless Dent Repair at Home

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Car Dent Remover

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Paintless Dent Repair Course

Salina

Paintless Dent Removal Techniques: How To Do It Yourself

If you are a vehicle owner, you have most probably heard of paintless dent repair. It is one of the most widely used techniques for fixing dents and similar types of damage to the car's body. Here you will find useful information about this repair method to help you get a clear idea of when it works best and when to use it.

What is it?

This is a technique used for flattening the dents on the body of a moving vehicle, and more specifically, on the panels. Special metal rods and picks are used to get behind the shell. Then the technician manipulates them to push out the dent. This is how the surface becomes flat once again. One interesting fact about paintless dent repair is that it's been around for over eight decades.

Is it effective for all dents?

The straightforward answer is: no, it isn't, but it's worth looking at the details. As its name suggests, this type of repair technique works only when the paint of the car is intact. If it is damaged, a different method must be used. It is typically more complex and time-consuming. Additionally, when the paint is damaged, time is of the essence for getting the panel restored fully. The good news is that the paint used by modern vehicle manufacturers is highly resistant to cracking, peeling and other types of damage.

Paintless dent repair is most effective for minor dents and creases, hail damage and dings. It would typically work well even if there are multiple dents or creases close together. A close professional inspection of the vehicle's damage is the best way to determine if this technique should be used or not.

Does it matter what material the panel is made from?

This repair method is regarded to be effective and safe for both steel and aluminum panels. It is not known to cause any changes to the structure of these metals that would make them weaker or more susceptible to rust and other types of damage. It is worth noting that with this technique, the paint of the vehicle will remain intact too, provided that it is applied correctly, of course.

Can I do the job it myself?

Theoretically, you can. The tools needed for paintless dent repair are readily available and don't cost a small fortune to buy. There are also plenty of online videos showing you how to apply the technique correctly. Still, if you don't have sufficient knowledge and skill, you risk causing further damage to your vehicle. That is why DIY repair is not a very good idea.

How do I choose a professional paintless dent repair service?

Confirm that the technician who will do the job has received specialized training and has sufficient experience. Ask about the warranty provided before hiring the service. Leading providers usually cover their work with a lifetime warranty. In general, you should know that this type of repair job doesn't take a long time to complete so you should expect to get your vehicle fully fixed in days rather than weeks, unless there is a waiting list.

Car Dent Repair

Paintless dent removing is increasingly becoming popular day by day as it is not only a time saving technique, but is also cost effective and efficient. These techniques are the best solution for minor dents and actually result in your car looking brand new. Even a trained eye will not be able to detect where the dented area was.

One of the most common reasons why PDR is used is to repair hail damage, minor body creases, door dings and minor bumper indentions. This technique can also be used to help prepare the damaged panel for paint repair. In such cases it is referred to as push-to-paint or push-for-paint. One of the limiting factors that ails PDR is that it cannot be used for paint repair and the amount of metal that can be stretched by the incurred damage. And so many times sharp dents and creases may not be repairable at least not without a paint job.

In the recent years there has been a conscious effort to bring a standard to this trade and even The National Alliance of Paintless Dent Repair Technicians (NAPDRT) was formed in 2006. The mission of this organization is to educate consumers and to enhance the industry standards through third party certification and mutual accountability. To date however there is no industry wide certification process in the field of Paintless Dent Repairs.

Methods of Repair:
One of the most common methods of paintless dent repair is to utilise body picks and metal rods to push the dent out from the inner side of the panel that is being repaired. Also glue might be used from the exterior of the panel in order to pull the dents out. In either of the cases fine tuning of these repairs requires "tapping" down the repair in order to remove the small high spots so as to make the surface flat. PDR may use both steel and aluminum panels.

Fluorescent lighting or in some cases even light reflection boards are used to see the shadows that are created by the deformation of the dent. This is an extremely important aspect of the repair process as without the paintless dent repair light or the reflector board the fine detail of the process is unseen and the technician then cannot choose their tool specifically and repair the damage effectively.

The process of paintless dent repair needs the technician to specifically push the metal in the exact location to a precise height which can be seen or witnessed with a PDR reading instrument such as the PDR reflector board or the PDR light.

This trade needs some special PDR training which can be availed at a number of schools Australia wide. But if you are interested in the best then head down to Dents R Us. For more info please visit http://www.dentsrus.com.au.

Salina  

10 Things to Consider When Starting Your PDR Business

Auto Dent Removal

KANSAS Hail Damage Repair