Broomfield Paintless Dent Repair Process

PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Broomfield .

Paintless dent repair light

The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!

Pop a Dent

How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.

Dent Repair Cost

If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Broomfield  that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.

Paintless Dent Repair Process

Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.

Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.

Paintless Dent Removal

Roof: simply remove or lower the headliner.

Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.

Hood: remove the covering from the inside of the hood and access the ding or dent this way.

While doing these repairs, it should not require the technician to drill any holes.

Hail Damage Repair

Broomfield

What You Need To Know About Dents

It can be frightening when you get stuck in a hail storm but the truly scary part is what it can do to your car. You wouldn't think that little chunks of ice could do much damage to sheet metal. However, many people have been left with a car that looks like a golf ball after a nasty winter storm. Auto Hail Damage Repair has changed a lot over the years and can be done in some cases without the need for a new paint job.

For years the standard way to remove dents was by pulling the dent out. You would have to drill holes into the dented area and use a tool to pull the metal back into shape. Then you would have to grind the holes down and use a body filler to smooth them over. After that you would repaint the damaged area and that is one of the biggest drawbacks to this procedure. A paint job that was put on by the manufacturer is of extremely high quality. It is nearly impossible to duplicate it without taking it back to the manufacturer. So you would be left with a section of car that was obviously repainted with inferior materials.

Paintless Dent Repair was invented specifically for this reason. The Mercedes-Benz Company in Germany was having a lot of trouble shipping their cars to the various dealers. When they arrived they would have dents and dings but the car lot would not have the resources to give them a manufacturer quality paint job after they were repaired. So they developed a procedure for Paintless Dent Removal that uses rods to push the dent out from the inside while gently tapping the outside with a hammer. It is important that the technician be very skilled using Paintless Dent Repair techniques because if they strike the metal too hard it will split. Sometimes glue is used on the outside of the car to pull the dent instead of pushing with rods which can eliminate the need for using a hammer on the metal. The only times that Paintless Dent Removal is not possible is if the paint was damaged by the initial impact or if the metal has been stretched too far out of shape.

Paintless Dent Repair is a great way to save money and retain your original manufacturer paint job. Just make sure that the repair shop that you choose is reputable and has done it many times before. To find a local repair shop you can search the internet for Paintless Dent Repair North Georgia.

Auto Dent Repair

It can be frightening when you get stuck in a hail storm but the truly scary part is what it can do to your car. You wouldn't think that little chunks of ice could do much damage to sheet metal. However, many people have been left with a car that looks like a golf ball after a nasty winter storm. Auto Hail Damage Repair has changed a lot over the years and can be done in some cases without the need for a new paint job.

For years the standard way to remove dents was by pulling the dent out. You would have to drill holes into the dented area and use a tool to pull the metal back into shape. Then you would have to grind the holes down and use a body filler to smooth them over. After that you would repaint the damaged area and that is one of the biggest drawbacks to this procedure. A paint job that was put on by the manufacturer is of extremely high quality. It is nearly impossible to duplicate it without taking it back to the manufacturer. So you would be left with a section of car that was obviously repainted with inferior materials.

Paintless Dent Repair was invented specifically for this reason. The Mercedes-Benz Company in Germany was having a lot of trouble shipping their cars to the various dealers. When they arrived they would have dents and dings but the car lot would not have the resources to give them a manufacturer quality paint job after they were repaired. So they developed a procedure for Paintless Dent Removal that uses rods to push the dent out from the inside while gently tapping the outside with a hammer. It is important that the technician be very skilled using Paintless Dent Repair techniques because if they strike the metal too hard it will split. Sometimes glue is used on the outside of the car to pull the dent instead of pushing with rods which can eliminate the need for using a hammer on the metal. The only times that Paintless Dent Removal is not possible is if the paint was damaged by the initial impact or if the metal has been stretched too far out of shape.

Paintless Dent Repair is a great way to save money and retain your original manufacturer paint job. Just make sure that the repair shop that you choose is reputable and has done it many times before. To find a local repair shop you can search the internet for Paintless Dent Repair North Georgia.

Broomfield  

Auto Hail Damage Repair

Car Dent Remover

COLORADO Paintless dent repair light