PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Olathe .
The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!
How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.
If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Olathe that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.
Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.
Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.
Roof: simply remove or lower the headliner.
Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.
Hood: remove the covering from the inside of the hood and access the ding or dent this way.
While doing these repairs, it should not require the technician to drill any holes.
What is Paintless Dent Removal?
It can be frightening when you get stuck in a hail storm but the truly scary part is what it can do to your car. You wouldn't think that little chunks of ice could do much damage to sheet metal. However, many people have been left with a car that looks like a golf ball after a nasty winter storm. Auto Hail Damage Repair has changed a lot over the years and can be done in some cases without the need for a new paint job.
For years the standard way to remove dents was by pulling the dent out. You would have to drill holes into the dented area and use a tool to pull the metal back into shape. Then you would have to grind the holes down and use a body filler to smooth them over. After that you would repaint the damaged area and that is one of the biggest drawbacks to this procedure. A paint job that was put on by the manufacturer is of extremely high quality. It is nearly impossible to duplicate it without taking it back to the manufacturer. So you would be left with a section of car that was obviously repainted with inferior materials.
Paintless Dent Repair was invented specifically for this reason. The Mercedes-Benz Company in Germany was having a lot of trouble shipping their cars to the various dealers. When they arrived they would have dents and dings but the car lot would not have the resources to give them a manufacturer quality paint job after they were repaired. So they developed a procedure for Paintless Dent Removal that uses rods to push the dent out from the inside while gently tapping the outside with a hammer. It is important that the technician be very skilled using Paintless Dent Repair techniques because if they strike the metal too hard it will split. Sometimes glue is used on the outside of the car to pull the dent instead of pushing with rods which can eliminate the need for using a hammer on the metal. The only times that Paintless Dent Removal is not possible is if the paint was damaged by the initial impact or if the metal has been stretched too far out of shape.
Paintless Dent Repair is a great way to save money and retain your original manufacturer paint job. Just make sure that the repair shop that you choose is reputable and has done it many times before. To find a local repair shop you can search the internet for Paintless Dent Repair North Georgia.
Paintless dent removal is a good idea for those who have minor dents or dings they want to remove from their vehicle. It doesn't require major body work, and in most cases you can have your car back in as little as a day as opposed to several days to weeks with major body work. The cost is also much lower since the overhead is lower. There are some instances where paintless dent removal isn't possible. If you have a simple dent you want to have pulled out, here are a few things to consider.
How It Works
A technician that has been trained to use specialized tools will work on the dent locally. This means a dented door doesn't need to be removed. In most cases they will access the dent from the other side by going through a window opening or removing the door panel. The dent is then worked on from the inside, and pressed back out. It sounds simple, but it requires skill and patience. The technician needs to have experience in this so that they don't push the dent out too far or damage the surrounding paint. It is something you can do at home, but it's not suggested.
When Paintless Dent Removal is Feasible
Even large dents can be fixed with this method as long as the paint has not been shattered or cracked. If you have had previous body damage repaired in the area, this method may not work. Dents that are close to the edge of a panel are also difficult to repair with this method. The most common application for this method is door dents, dents on the hood or trunk, and dents on the roof. Hail damage can be repaired with this method, but it's a more lengthy process.
Benefits of Paintless Dent Removal
Paintless dent removal is advantageous for several reasons. For one, it's approved by most insurance companies. This means if you have damage that is covered by your auto insurance, you can get it repaired with this method and get your car back much faster. Since nothing is being replaced or removed, the vehicle will retain its factory value as well. You don't need to report body damage when you sell the vehicle. The dent won't need to be repainted or bonded in any way. When a vehicle is damaged and needs paint touch up on just a small area, it's very hard to match the color. Even if they use a color provided by the manufacturer, this doesn't take in to account the wear and tear the current paint job has, and can still stand out and be very noticeable. The turn around is also much faster. With traditional body repair you may have to relinquish your vehicle to the shop for several days, weeks for larger repairs. Paintless dent removal can be done in just a few hours and you can get your car back on the same day in many cases. Of course you want to call ahead to see what kind of schedule the technicians have, as this could hold up the process a bit. If you have to come out of pocket for the repair you will enjoy savings with paintless dent removal over traditional body work.