PDR stands for paintless dent repair. It’s a craft that you can learn and it will, once you have mastered the skill, be a way for you to earn a very nice income. You will be able to remove those dings from car doors, and other small dents that you will find around the automobile. This doesn’t take long if you are experienced at doing it. It normally takes 10 to 20 minutes and is very inexpensive, since there is no product to buy. PDR is becoming the alternative to body shops in Moore .
The biggest reason people are choosing this method over a body shop is the time that it takes at a body shop to repair a dent, and also the money they are spending to get it fixed. With PDR, not only will the time your vehicle is being repaired be shorter, but also it will cost you so much less money. It’s a new way of fixing dents and dings that is putting the car repair world at notice!
How exactly does paintless dent repair work? A person who has been trained at PDR will use metal rods and picks in order to massage out dents and dings from the finish of the car. This will be done by the expert working from the inside of the car or panel, depending on where the dent or ding is. In essence, the dings and dents are being pushed out. A normal repair from beginning to end will last about 10 to 20 minutes.
If you want to try and do this as a living all you need is to purchase the tools, get the training, and offer a service where you will go to people and fix the dents and dings, or get a shop and do the service from there. This is a very high-demand service in Moore that many people are looking to have done now. It depends on where the dent or ding is in the vehicle and how you will access it. Here are some of the more common areas and how to go about accessing it.
Doors: You will need to roll down the window, and access the area by the window ledge opening. There may be an existing opening in the door jam. Access through this spot. Take the panel off the door, or even drill a hole in the door. You can finish this off by putting a silicone plug into the hole to prevent any corrosion, and to make the door look good.
Rear quarter panels: There should be an opening or even a vent in the rear door area. Access through this spot. Go through the trunk, or through a tail light assembly. You can access the dent through the wheel well, or drill a hole through the rear door. Of course, you will need to plug it when finished.
Roof: simply remove or lower the headliner.
Front fender: go through the engine compartment, or through a headlight assembly. Again you could access this from the inner wheel well too.
Hood: remove the covering from the inside of the hood and access the ding or dent this way.
While doing these repairs, it should not require the technician to drill any holes.
Paintless Dent Repair - The Truth, Myths and Misconceptions
Paintless dent removal (PDR) has become popular in the last few months with auto body shops around the country as a method of fixing dents on the body of motor vehicles. What is PDR and what can it do for you?
Paintless dent removal is a method of repairing dents and dings without the use of paint and fillings. During the process, a PDR technician uses metal rods and body picks to push out dents.
Why the popularity
PDR techniques have enjoyed a growing popularity with auto repair shops recently because of its obvious advantages: PDR is faster, convenient and very inexpensive, compared to traditional dent repair methods.
The most remarkable advantage of PDR is probably that it does not require the use of paint. The paintless dent removal technical only uses tools to repair car dents, leaving a minimum of marks.
The car does not need re-spraying and this brings down your overall costs.
Secondly, paintless dent removal is fast. From beginning to end, the process takes only about half and hour, sometimes even less. For that reason, PDR can be performed in the convenience of your home or office: you do not need to leave your car for entire days at the auto body shop.
Finally, your car gets to keep its original paint: no color mismatch or over-spraying.
Is paintless dent removal for you?
As for any type of repair technique, paintless dent removal has limitations and cannot fix about any car damage.
PDR techniques should also be used with a lot of caution on older cars and on cars with a fragile coating. An inexperienced technician could easily cause the coating to crack during the PDR.
The size of the dent is also an important consideration. Big dents are hard to remove without leaving marks. In fact, the larger the dent, the more pressure was exercised on the metal. An inexperienced technician could cause a lot of damage by trying to repair a big dent using PDR.
Finally, dents may be located areas difficult to reach. It may therefore require a lot of time to reach those dents and fix them. Most specialists in such cases could simply advice a respray.
Most cities have reputable paintless dent removal shops. However, before you take your car to a specialist, it is important you know what it can do for you.
If you get dents in your car your initial reaction is to be shocked, the next reaction is to get angry and the third reaction is to calm down and take the necessary steps to fix the issue. But, when it comes to fixing the issue, are you fixing it in the proper manner? In other words, are you still keeping to long established methods of fixing a dent as opposed to taking advantage of the far more cost effective process of paintless dent repair?
When something novel comes along there will be those people who will move at the opportunity to use the innovations that new methods have to offer. Then again, there will be those people who may not like trying something new simply because they are more familiar with an original process they are familiar. (This is why some people still buy videos and will not to upgrade to DVD.) While this gripping on to the old may seem rather gracious, it can also prove to be a waster of time and extremely expensive. One such example of this can be found in the car world in the form of sticking with traditional bodywork as opposed to paintless dent repair.
For those not familiar with paintless dent repair it references a method when a dent is molded into the car's original form without the requirement of repainting the car. Now, this may seem like a radical diversion from the usual process of fixing and repainting a dent. Obviously, that's because it is! It is also a much more cost effective process of repair as it eliminates the extra costs involved with repainting the finish of an automobile. Yes there is the possibility for a number of unplanned expenses associated with the repainting of a car's finish. In some instances, the new finish may not match the old finish and this can lead to a notable devaluing of the car. (Envision paying a ton of cash in repairs and finishing up making the car's trade in value go down!) As many understand, the possible expenses involved with refinishing the paint on a car can be huge so why not consider paintless dent repair and skip this step?
Once again, the issue is commonly an observance to tradition. That is, car repairs become a member of the "this is the way we always did it and this is the way we will continue to do it" methodology. However, if most people prescribed to this thought pattern we would not be driving automobiles...we would be riding around on horses! Sure, paintless dent repair may look like a radical deviation from what was done before but it is a valuable process that is a much more cost effective improvement over the bigger task methods of the past. As a result of this paintless dent repair is a much wiser solution for your minor repair needs. After all, it is a sensible method that is free of a number of the common nuances involved with old fashioned repair work. Clearly, that is a better module to choose.